Product Description
Two-component iron oxide epoxy red oxide primer, which offers good cutting performance as well as being weld ab e. It has excellent corrosion resistance properties.
Recommended Usage
As a pre-fabrication primer for the steel during fabrication and assembly. Good cutting performance.
Technical Data
| COLOUR | FINISH | SOLID BY VOULME | THEORETICAL SPREADING RATE | FLASH POINT | DRYING CHARACTERISTICS | SHELF LIFE |
|---|---|---|---|---|---|---|
| Red | Matt | 25+2% | 10.00sq.mt/Ltr at recommended DFT of 25p | Base: Above 230 C Hardener : Above 230C | SURFACE DRY : 5 minutes DRY TO HANDLE: 10 minutes FULL CURE: 7 days |
Base : 6 months Hardener : 6 months |
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to SSt-2/sSt3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data
MIXING RATIO: Base : Hardener (As per our recommendation) APPLICATION: By Brush / By Conventional Spray / By Airless Spray THINNER: Our Epoxy Thinner.
POT LIFE at 300 C : Minimum 16 hours at 300C.
RECOMMENDED DFT:20 – 25p.
OVERCOATING INTERVAL:MIN : 8 hrs.
MAX : Indefinite.
COMPATIBILITY: Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Application Procedure
Stir the Base part thoroughly. Mix the base and hardener in there recommended ratio by volume. Stir the mix thoroughly to attain in homogeneity. Allow the mixture to (maturation) for about 10 min to initiate the reaction. Add Our the mix, depending on application method, and stir thoroughly for few minutes Strain the paint through Nylon filter cloth ply uniformly over the All equipment’s used for above should be proper need. Application: By Conventional Spray / By Airless Spray.
For Conventional Spray application:For Airless Spray Application.
Thinner:Our Epoxy Thinner Thinner : Our Epoxy Thinner.
Addition: 2-5%Addition : Max 20 If required.
Nozzle Orifice: 1.2 — I .4mm NozzIe office : 0.46-0.79.
Nozzle Pressure:40-70 p.s.i Nozzle Pressure : 1250 p.s.i. min.
Additional Information
Further information regarding industry standards, term and abbreviations used in this data sheet can be found in the following section of Pacific Paints test Data manual: – Guide to Product data Sheet -Surface Preparation Details -Paint Application Details -MSDS.
Note
Do not apply paint when temperature falls below ICC or rise above 500C and when Relative Humidity is above 85%. Do not apply during rain, for or mist. Surface temperature must always be minimum of 30C above Dew point. 2. Brushes and spray equipment should be cleaned with PPI’s recommended thinner, otherwise equipment is liable to be damaged. 3. DFT variation can be obtained by change in application method/thinning ratio. Contact Pacific Paints representative for further assistance. 4. Shelf life indicated is minimum for this Product in sealed condition and it is subject to re-inspection thereafter. Individual component is required to be stored in cool, dry and covered condition, away from heat and ignition. Type here to search.
Health & Safety
This is a solvent based paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.
Limitation of Liability
To the best of our knowledge, the technical data in our literature are true and accurate at the date of issuance but are subject to change without prior notice. We guarantee our product to confirm to the specification contained herein. We make no other warranty or guarantee of any kind, express or implied, including merchant ability and fitness for particular purpose. Liability, if any, is limited to replacement of the product or refund of the purchase price. Labor or cost of labor and other consequential damages are hereby excluded.
